Let us elaborate you how to light pilot on gas fireplace. A fireplace pilot, often known as merely the pilot in a gas room, is a critical component of gas stove setup and is crucial for assisting propane furnace flames in igniting fast and effectively. Some gas fixtures include a running starter light, and it’s a bit blaze that remains even though the fire pit is not in use.
It allows igniting the interior when it’s chilly outdoors. Still, when you’re not utilizing the interior throughout the summer, it’s better to turn off the starter to save propane. When you do, you must resume it in the following winter weather.
In this post, we’ll go over how to light pilot on a gas fireplace and most of what you require to understand about gas fireplaces’ starter lights. Read more about pilot lights and valuable hints for doing the work safely.
The phrase pilot or starter light alludes to the tiny, less apparent flame seen as a component of the igniting mechanism within a gas furnace. The pilot is a combustion element since an ignitor is needed to supply the charge that fires this flare.
Once you switch on your furnace, gas flows via the section of the pipe to the core burner. When released from the primary burner, the gas burns and connects with the starter light or sparking ignition coil.
For perspective, the starter light is a continuously glowing flame utilized to spark the gas emitted by the core burner. A sparking ignitor is a contemporary technology that uses an electrical charge to burn the gas. Let’s look at how to light the pilot on gas fireplace.
How To Light Pilot On Gas Fireplace?
Let’s get into the process.
Read the Instructions
Please remember you thoroughly read the supplied handbook before lighting the fireplace. Although many fireplaces employ similar techniques for firing up, yours might differ from others. It might be pretty dangerous if not handled correctly.
Switching on the Gas
Lift the fireplace’s ornamental top to uncover the gas valves at the unit’s base, low to the ground. There should be a propane shut-off lever visible. Turn the knob in the opposite orientation of the gas pipelines to switch on the gasoline.
If you can’t find the lever, it gets most likely hidden behind the log fire. Search for that and activate it there. If your fireplace has a permanent glass panel, take it off. This critical safety measure avoids gas accumulation if the pilot is difficult to ignite.
Note: Check that the auxiliary gas cutoff on the log fire is fully engaged. These valves are typically situated outside the log fire and activated by a unique key.
Illuminating the Pilot
Find the propane regulator valve, which seems to include pilot, on, then off positions. Find a red or black pushbutton; that’s the piezoelectric flame igniter. Push a button several times to ensure that a flame appears at the tip of the starter rod. This charge will light the starter flame.
Note: Natural gas has far-reaching impacts, and natural gas seems to be a potent and potentially hazardous chemical. When working with propane, you must adopt all necessary care.
Adjust the propane regulator lever till the “Pilot” position matches the arrowhead or cross point on the controller’s outside rim. Holding up the gas regulator dial and then pushing the ignition source switch several strokes until the starter light starts.
Holding up the gasoline-controlling dial for 30 to 45 secs after the pilot illuminates to enable room for the thermostat, a protection mechanism, to warm up, then let the dial, so it rises. If the flame does not ignite, turn the gas regulator dial until it rises, and also the supply of gas gets stopped.
Allow 15 seconds before repeating the illumination procedure till the pilot begins to fly. Return the permanent glass unit and ornamental covering after turning the gas regulator dial to “On.”
Key-operated Gas Fireplace
Several propane fireplaces utilize a metallic key to regulate the stream of propane. For, How to light the pilot on gas fireplace using a key, follow these procedures
Read the Owner’s Guide
Before turning on the gas fireplace, carefully read the attached handbook. Although most fireplaces employ similar beginning procedures, there are variations across models. Unintentional errors have the potential to be catastrophic.
Take away the Front Section
A glass panel often separates the fire compartment from the entire space in gas fountains. To begin, switch on the fireplace by removing the crystal barrier.
Put the key into the valve
Now, locate the gas orifice near the log fire. To use the gas lever, put the key into it. Wait till you get set to ignite the burner before turning the key. If you flip the key before you are ready to light the flame, you risk releasing too much propane and causing a small explosion.
To start the burner, you’ll require a lengthy lighter. A barbecue skewer is an excellent tool for securely lighting your fireplace units. To begin, use your extended lighter to start the firebox burner. Next, while maintaining the blaze against the heat source, rotate the gas inlet stem clockwise.
Your fireplace will now be operational. Restore the front crystal screen on your log fire. Using the gas regulator key, you would regulate the fire. Rotating the propane key to the left will amplify the flares while flipping the key to the right will extinguish them.
Adore those pleasant cold nights by the blazing fire because now you understand how to securely light and utilize the gas fireplace. There could be a vacuum in the starter tubing if the furnace is new or the light doesn’t get lit for a considerable period.
It makes it challenging to ignite, but after many efforts, it must burn. If you find yourself needing to ignite the starter often, the starter tubing could get clogged with dirt, so use a needle to clear the tip of the tubing.
Check Out This Video,
VIDEO CREDITS: AdamDIY YouTube Channel
More Like This: Check Out These Related Articles